# Furring Strips

Birch plywood furring strips, 3 3/4 in by 3/4 in, on the walls of a 2026 Ford Transit T-250 148 in wheelbase High Roof. Tick the strips you need; the crosscut list sorts them by length. Wall heights and starts are guesses until measured.

[Open the configurator](index.html) · status: **draft**, version 0.2

The strips are already ripped. The page shows where each one runs on the walls and gives the crosscuts. Nothing on this page is 3D printed, so the Filament and 3D printing panels stay hidden.

## Strips

Fifteen strips as measured, numbered bottom to top on each wall. D is the driver side (left, facing forward), P the passenger side. F runs ahead of the C pillar, R behind it.

| Wall | Strips, bottom to top | In My cut |
|---|---|---|
| Driver front | DF1 53 3/8, DF2 56 5/8, DF3 46 1/2, DF4 46, DF5 45 | DF1, DF2 |
| Driver rear | DR1 63 1/8, DR2 62 7/8, DR3 64 1/2, DR4 64 1/2 | DR1, DR2, DR3 |
| Passenger rear | PR1 62 3/4, PR2 62 3/4, PR3 64 1/4, PR4 64 | PR1, PR2, PR3 |
| Passenger front | PF1 45 3/4, PF2 45 | none |

All 15 strips are on by default: 847 in (70 ft 7 in) before kerf. The My cut preset leaves out strips under 47 in and the top strip on each rear wall: 8 strips, 490 1/4 in.

## Settings

- **Crosscut list**: the included strips, longest first, with a Cut box per strip. Cut marks stay in this browser; Clear the marks resets them.
- **Each wall**: where its strips start, measured from the B pillar, then per strip an include checkbox, the length and the height of the bottom edge above the floor. A picture of the wall, seen from inside, shows the strips to scale.
- **View**: both walls or one, the van skin or ribs only, and left out strips as red outlines.

## Presets

- **All 15 strips** (default): every strip as first measured.
- **My cut, 8 strips**: no strips under 47 in, no rear tops, nothing on the passenger front.
- **Rear walls only**: DR1 to DR3 and PR1 to PR3.

## Views

From the rear (opening view), Driver wall and Passenger wall, plus the kit's Angle, Front, Back, Side and Top. Pick one wall under View before a wall view to drop the far half of the body.

## The van body

A see through stand in built from Ford's cargo numbers for the 148 in High Roof: 81.5 in cargo height, 143.7 in floor length, 70.2 in max width, 54.8 in between the wheel wells. Not a scan.

Guesses to confirm in the van:

- Where each wall's strips start: 2 in behind the B pillar on the front walls, 74 in on the rear walls.
- Every strip height.
- Rib positions and depth (1 1/4 in), and the C pillar from 62 to 72 in.
- The wall runs plumb to 48 in, then curves in 7 in by 78 in.
- Sliding door opening from 2 to 53 in, 64 in tall.
- Wheel wells from 66 to 102 in, 13 in tall, 7.7 in deep.

The page warns when a strip crosses the sliding door, hits a wheel well, runs past the rear doors, or overlaps its neighbor.

## Exports

A PNG of the view on screen, and a JSON file with every setting. The Copy link button carries the settings.

## Files

    index.html    page shell; loads the shared kit from ../../kit/
    model.js      settings, presets and build(), the geometry engine of record (JS, manifold-3d)
    model.json    title, summary, visibility, version and changelog
    thumb.png     catalog card art

Needs a network connection: three.js loads from a CDN, as on every kit page.

## License

© Ryan Mitchell — CC BY 4.0. See [LICENSE.txt](../../LICENSE.txt).