Models you configure, not just download — for laser cutters & burners, CNC routers and plasma tables, and 3D printers. Set your dimensions in the browser, get a 1:1 file for your machine.
Rigid MOLLE panels on the true PALS grid: size & style presets (seat backs, 30×20 tech panels, van-window trapezoids), slot shapes, webbing channels, corner slits, nesting, kerf compensation, weight estimates, edge engraving, and a live 2D/3D preview. Exports cut and engrave SVGs ready for XCS or LightBurn.
Printed mounts that clip over a plywood edge in a van, all on one U clip you fit once: switch and socket panels, a junction box, AirMini and phone holders, a cable wrap, hooks, shelves and cup rings. Prints with no supports, with a live 3D view, presets and a print check. Exports 3MF for Bambu Studio or Orca, and STL.
A printed shim that holds a furring strip off a van wall rib. Flat or wedged to match the curve of the wall, with a screw hole or slot.
Fastens a furniture base to one row of floor L-track with two double lug threaded studs. Nuts sit in covered pockets you reach from above. Printed feet level the far side.
Rough mockups of van furniture and gear on one row of floor L-track with two threaded studs. Each idea shows a different way to attach and build the base.
Four 3/4 in plywood strips cut on the CNC that fill the gap at the edge of the van floor. A and C run the same way, B turns between them, and D stands off A like B. The 3D printing panel applies to the printed brackets only.
A detent strip for the sliding door track. The roller climbs a ramp, drops into a curved cup and holds the door until you push it out.
A Contura style rocker actuator that clips onto the switch pivot pins. Flat, crowned, dished or half rocker faces, with text, icons or your SVG inlaid in a second color. Prints one cap, a batch or a tolerance test set.
Full Transit 148 HR garage on the wheel well cabinet engine: driver and passenger cabinets with electrical, water or storage roles, drag and collision checked placeholders, bed platform and clear height, slide out bike tray with derated slides, L-track, MOLLE, 80/20 mode, garage BOM and DXF sheets for VCarve.
Flat 12V mounting plates for the Transit, trekMount style: one plate, a side by side pair or a cabinet pair, with an optional Charger 2 plate. Checks keep outs and material webs, then exports cut SVG and DXF, a 1:1 template PDF, a hole table and the printed spacer.
A printed box for van switches: any mix of Contura II and round rockers, with spare positions and engraved labels, on a cabinet face, a wall or L-track, flat or tilted.
Sliding comb plywood bed for a Transit T-250 148" HR: two interleaved combs from one 4x8 sheet, animated slide, mattress layouts, rear wing and cubby, live dimensions, and DXF cut files for the front, wing and lip.
Printed fittings for 3 in flexible heater duct: couplers, elbows, Y adapters, end caps, an inline damper, a panel register, wall outlets on an M6 rivnut or magnets, a boot dryer, a hose saddle and a thread test set. The thread copies the Velit directional vent.
Small coupons for dialing in prints: a support ladder for built in breakaway ribs and every slicer support strategy, overhang angles, bridges, horizontal holes, peg fits and flex arms. Each coupon prints flat with stamped values.
Birch plywood furring strips, 3 3/4 in by 3/4 in, on the walls of a 2026 Transit 148 in High Roof. Tick the strips you need; the crosscut list sorts them by length. Wall heights and starts are guesses until measured.
A printed trim for the 90 degree edge of a piece of wood: a corner angle, an edge cap, or a step (S) profile, straight or as a corner piece, with an optional LED channel (a tray with a top, back and bottom in the space behind the face) for a 10 mm strip. Every leg and flange takes its own length and thickness.